Test kabinleri

Simulate the perfect atmosphere for climate and temperature tests, specifically in accordance with DIN EN 60068-2-1, 2-2 and 2-3. Provide unlimited flexibility for controlled material and function tests as well as ageing tests.

Standard equipment
Ventilation and Control:

• high-performance air fan in working chamber
• depending on operation status automatically variable fan speed with manual adjustment from 10% to 100%
• adaptive, fuzzy-supported multifunctional digital microprocessor PID-controller
• autodiagnostic system with fault indication on temperature and humidity control
• 2 x Class A, 4-wire circuit, Pt100 sensors, mutually monitoring and maintaining performance at the same temperature value
• digital 7-day-programme-timer with real time clock, precise minute setting
• integral timer for heating profiles of up to 40 ramps, each segment adjustable from 1 min. up to 999 hours
• digital display (LED) of all set parameters, such as temperature, weekdays, time, humidity and set-up values - language to be chosen in setup
• digital display of set values (resolution: 0.1°C below 99.9°C, 0.5°C above 100°C) and actual values (resolution: 0.1°C) of temperature (LED)
• long-term documenting (ring store) of all relevant data, GLP-conforming as data logger - 1024 kB
• programme stored on power failure
• parallel printer interface (incl. real-time clock with date function) for all PCL3-compatible ink-jet printers for GLP-conforming documentation
• USB interface including Memmert "Celsius" software for programming and documentation
• chip card control incl. one MEMoryCard XL with 32 kB (up to 40 ramps)
• incl. works calibration certificate for -20°C and +160°C

• high-performance ring heaters with optimised air circulation
• door heating to avoid condensate

• twin compressor
• speed adjustable condenser fan
• refrigerant R404A

• with audible and visual alarm in case of over-/undertemperature and over-/under-humidity, open door and empty water tank
• independently working, digitally adjustable electronic overtemperature controller, TWW protection class 3.3
• additional adjustable Auto-Safety-Function "ASF" for over- and undertemperature automatically following the set value at a preset tolerance range
• mechanical temperature limiter TB class 1 switching the heating off at approx.10°C above max. oven temperature

• Electronically controlled active humidification and dehumidification from 10% to 98% rh with digital display of the relative humidity, display resolution 0.5%, setting accuracy 1%
• incl. works calibration certificate for +30°C at 60% rh
• Humidity supply with distilled water from 2 x 10 l tanks on integrated telescopic slide, with automatic water tank change-over
• 2 x 10L tanks acting as condensate collectors, on telescopic slide mounts

For long-term stable temperature/humidity simulations in one chamber. The constant climate chambers are ideal for norm-compliant work according to ICH guidelines and work independently of the water supply.

KBF P Series: Constant climate chambers with ICH-compliant lighting and variably positionable light cassettes.
KBF LQC Series: Constant climate chambers with ICH-compliant light source and patented light dose control for UV-A and VIS. Temperature range: 0 °C to 70 °C and humidity range: 10 % RH to 80 % RH.

Equipment:

• Electronically controlled APT.line™ preheating chamber with cooling system
• Inner chamber made of stainless steel
• Intuitive touchscreen controller with time-segment and real-time programming with internal data recording
• Humidity regulation with capacitive humidity sensor and vapor humidification
• Inner glass door with seal
• Independent temperature safety device class 3.1 (DIN 12880) with optical and audible temperature alarm
• Avoidance of glass corrosion by special TIMELESS coating
• Access port with silicone plug diam. 30mm, left side
• Door heating
• Ethernet interface for communication software APT-COM™ DataControlSystem
• Internal data logger, measured values can be read out in open format via USB
• Power supply 200 ... 230 V, 50/60 Hz

For long-term stable temperature/humidity simulations in one chamber. The constant climate chambers are ideal for norm-compliant work according to ICH guidelines and work independently of the water supply.

KBF Series: Constant climate chambers with large temperature range: 0 °C to 70 °C and humidity range: 10 % RH to 80 % RH.
KMF Series: Ideal for demanding stress tests, e.g. at 85 °C and 85 % RH. Temperature range: -10 °C to 100 °C and humidity range 10 % RH to 98 % RH.

Equipment:

• Electronically controlled APT.line™ preheating chamber with cooling system
• Inner chamber made of stainless steel
• Intuitive touchscreen controller with time-segment and real-time programming with internal data recording
• Humidity regulation with capacitive humidity sensor and vapor humidification
• Inner glass door with seal
• Independent temperature safety device class 3.1 (DIN 12880) with optical and audible temperature alarm
• Avoidance of glass corrosion by special TIMELESS coating
• Access port with silicone plug diam. 30mm, left side
• Door heating
• Ethernet interface for communication software APT-COM™ DataControlSystem
• Internal data logger, measured values can be read out in open format via USB
• Power supply 200 ... 230 V, 50/60 Hz

Homogeneous lighting conditions with constant temperature and humidity conditions, the BINDER growth chambers. The responsive humidification system, the high-performance cooling and uniform light distribution ensure optimal growth conditions.

KBW Series: Growth chambers with light
KBWF Series: Growths chambers with light and humidity

Equipment:

• Electronically controlled APT.line™ preheating chamber
• Temperature range 0 °C to 70 °C (without humidity and illumination)
• Humidity range 10 % to 80 % RH (KBWF)
• Variable position illumination cassettes each with 5 daylight fluorescent illumination tubes
• Controller with time-segment and real-time programming
• Humidity regulation with capacitative humidity sensor and vapor humidification (KBWF)
• Independent temperature safety device class 3.1 (DIN 12880) with optical and audible temperature alarm
• Interface: Ethernet, RS 485 (optional)

The Memmert humidity chamber HCP - This climate chamber offers a full range of comfort, reliability and safety. This humidity chamber is ideally suited for environmental testing, environmental simulation, accelerated service life tests and 85/85 tests according to IEC 60068-2-67 and IEC 60068-2-78.
The active humidity control is the guarantee for ideal homogeneity of temperature and humidity as well as for short recovery times after opening the door. In combination with heating on all six sides, including heated inner glass door, it also minimises vaporisation in the interior and thus the risk of condensed water dripping onto the test object. An aluminium thermal conductive layer supports optimum temperature distribution and serves as a heat accumulator in case of a temporary power failure.

Model variant TwinDISPLAY: ControlCOCKPIT with two colour displays
You can find a detailed description of the "TwinDISPLAY" model at www.memmert.com

Light module cold white 6.500 K: LED strips arranged on the side walls of the interior, 10 for model 110; 14 for models 260, 410 and 750; programme controlled dimming from 0 to 100 % (in 1 % steps); ramp programming in combination with temperature and humidity

Light module cold white 6.500 K + warm white 2.700 K: LED light strips - 10 strips for model 110; 14 strips for model 260, 410 and 750 (5 resp. 7 alternating cold white light strips and 5 resp. 7 warm white light strips); on the side walls of the interior, programme controlled dimming from 0 to 100 % (in 1 % steps); ramp programming in combination with temperature and humidity

The climate chamber generation with the unique ControlCOCKPIT for a quick and intuitive operation. Unparalleled temperature and humidity homogeneity for long-term stable ambient conditions. Specially designed for testing pharmaceutical products according to ICH, Q1A and Q1B, option 2, and similar global standards for stability tests of cosmetics and food.
Standard equipment :

• PID microprocessor control with integrated auto-diagnostic system
• Interior stainless steel 1.4301 (ASTM 304), deep-drawn
• Structured stainless steel housing, rear of zinc-plated steel
• High-Operation and adjustment of all parameters directly at the ControlCOCKPIT temperature connectors on the rear of the appliance for single-phase power connection according to country specific systems and IEC standards
• Internal data logger with a storage capacity of at least 10 years
• German, English, French, Spanish language settings available on the ControlCOCKPIT
• Digital backwards counter with target time setting adjustable between 1 minute and 99 days
• The SetpointWAIT function guarantees that the process time does not start until the set temperature is reached at all measuring points - optional for temperature values recorded by the freely positionable Pt100 sensors inside the chamber
• Adjustment of three calibration values for temperature and additional appliance specific parameters directly at the ControlCOCKPIT, for example relative humidity
• Moisture tight standard entry port, at the back, 40 mm inner diameter, can be closed by silicone stopper

• Available parameters on the ControlCOCKPIT: Temperature (Celsius or Fahrenheit), programme time, relative humidity, time zones, summertime/wintertime
• Two Pt100 sensors DIN class A in a 4-wire circuit for mutual monitoring, taking over functions in case of an error
• AtmoCONTROL software on a USB stick for programming, managing and transferring programmes via Ethernet interface or USB port
• ControlCOCKPIT with USB port for uploading programmes, reading out protocol logs, activating the User-ID function
• Displaying of already logged protocol data on the ControlCOCKPIT (max 10,000 values correspond to approx. 1 week)
• Ethernet interface on the rear of the appliance for reading out the protocol log and for uploading programmes and for online logging
• Multiple overtemperature protection: Electronic temperature monitoring TWW/TWB (protection class 3.3 or 2 and mechanical temperature limiter TB (protection class 1) acc. to DIN 12880, AutoSAFETY automatically adjusts to the set value within a freely adjustable tolerance range. Setting individual MIN / MAX values for over/undertemperature alarm

The cooled incubators with the unique ControlCOCKPIT for a quick and intuitive operation. Ideal at temperatures around zero and below. For rapid and precise alternation between heating up and cooling down times in ramp operation. Extraordinarily quiet.

Standard equipment :

• PID microprocessor control with integrated auto-diagnostic system
• Interior stainless steel, material 1.4301 (ASTM 304) very stable and easy to clean
• Structured stainless steel housing, scratch-resistant, robust and durable; rear of zinc-plated steel (all sizes mounted on lockable castors)
• High-temperature connectors on the rear of the appliance for single-phase power connection according to country specific systems and IEC standards
• Internal data logger with a storage capacity of at least 10 years
• German, English, French, Spanish, Polish, Czech, Hungarian language settings available on the ControlCOCKPIT
• Digital backwards counter with target time setting adjustable between 1 minute and 99 days
• The SetpointWAIT function guarantees that the process time does not start until the set temperature is reached at all measuring points - optional for temperature values recorded by the freely positionable Pt100 sensors inside the chamber.
• Adjustment of three calibration values for temperature and additional appliance specific parameters directly at the ControlCOCKPIT

• Available parameters on the ControlCOCKPIT: Temperature (Celsius or Fahrenheit), fan speed, exhaust air flap position, programme time, time zones, summertime/wintertime
• Two Pt100 sensors DIN class A in a 4-wire circuit for mutual monitoring, taking over functions in case of an error
• AtmoCONTROL software on a USB stick for programming, managing and transferring programmes via Ethernet interface or USB port
• ControlCOCKPIT with USB port for uploading programmes, reading out protocol logs, activating the User-ID function
• Displaying of already logged protocol data on the ControlCOCKPIT (max 10,000 values correspond to approx. 1 week)
• Ethernet interface on the rear of the appliance for reading out the protocol log and for uploading programmes and for online logging
• Multiple overtemperature protection: Electronic temperature monitoring TWW/TWB (protection class 3.3 or 2) and mechanical temperature limiter TB (protection class 1) acc. to DIN 12880, AutoSAFETY automatically adjusts to the set value within a freely adjustable tolerance range. Setting individual MIN / MAX values for over/undertemperature alarm